Cremation Handle
Reinforced plastic coffin handle 9522 in gold
Ref 9522
PP recycle
Lifts 50kg/pc
MOQ 1000pcs
Reinforced plastic coffin handle 9522 in gold, reinforced coffin handle, plastic coffin handle, funeral handle, coffin and casket handle
The 9522 handle is made by pp recycle, it can lift the wight 50k/pc, the color will be gold, silver or copper.
Drawings and reference photos are welcome on WhatsApp or by email. We do not use web forms.
Material
PP recycle
Lift weight
50kg/pc
MOQ
1000pcs
Lead time
30days
Key Benefits
Why This Model Is Specified
Tested Lift Weight
This model is rated at 50kg/pc. Load bearing models are checked on our own lift weight rig rather than quoted from a catalogue.
Light And Low Cost
Injection moulded and vacuum metallized, so the piece reads as metal at a fraction of the weight and unit cost.
Finish Options
Available in Gold, Silver or Copper. The approved tone is recorded so a repeat order matches the first one.
Hand Polished Before Finishing
Plating cannot hide a poor surface, so cast parts are hand polished before they go to the plating line.
Made On Our Own Tooling
The mould is ours and sits in our Wenzhou factory, so a re-order runs from the same tool rather than a copy.
Application Scenarios
Where It Is Used
- Cremation coffins in chipboard MDF or veneer
- Economy burial coffins for high volume programmes
- Rental and ceremonial coffins where weight matters
- Export ranges where freight cost per unit is critical
Who It Is For
Buyers Who Specify This Item
- Cremation coffin manufacturers
- Producers of economy and mid range coffins
- Funeral hardware importers and wholesalers
- Funeral homes and funeral directors
Problems It Solves
What Goes Wrong Without It
- Fittings sold without a stated load figure. This one is rated at 50kg/pc per piece.
- Plating tone that drifts between orders so a re-order will not sit next to earlier stock.
- Waiting on a supplier who has to sub-contract the tooling before anything can be made.
- Cast metal cost on a coffin that will be cremated within days of delivery.
Not sure this is the right reference?
Send a photo of the fitting you are trying to match on WhatsApp and we will identify the closest reference in our catalogue.
Talk To An EngineerTechnical Features
Specification Summary
| Material | PP recycle |
|---|---|
| Production route | Injection by mould and Vacuum metalization coating |
| Finish options | Gold, Silver or Copper |
| Size | 26.5*10.2cm |
| Rated lift weight | 50kg/pc |
Specifications
Full Specification Table
| Ref No. | 9522 |
|---|---|
| Lift weight | 50kg/pc |
| Production Route | Injection by mould and Vacuum metalization coating |
| Material | PP recycle |
| Size | 26.5*10.2cm |
| Finish | Gold, Silver or Copper |
| MOQ | 1000pcs |
| Lead Time | 30days |
Figures are taken from our production specification for this reference. Where a value is not listed we would rather leave it blank than estimate it, so please ask and we will confirm from the factory.
Materials And Manufacturing Process
How This Item Is Produced
Material for this reference is PP recycle. The stated production route is Injection by mould and Vacuum metalization coating.
Tooling
The mould is cut and trialled in our own workshop.
Injection
ABS or PP is injection moulded to the mould form.
Vacuum metallizing
A metal layer is deposited under vacuum.
Colour coating
Gold, silver, copper or bronze tone is coated over the metallized layer.
Inspection and packing
Pieces are checked for coating defects, counted and packed.
Quality Control
What We Check Before Packing
- Incoming material is checked before it goes into the casting or moulding cell.
- Castings and mouldings are inspected in process, not only at the end of the line.
- Load bearing models are checked on our own lift weight test rig.
- Plating and coating tone is compared against the approved reference sample.
- Counting and packing are checked before the carton is closed.
Documents
What Can Travel With The Order
Packing list, material description and the lift weight test record for load bearing models can be issued with the shipment. Ask before the order is confirmed so the paperwork is prepared in time.
Customization Options
What Can Be Changed
- Finish and tone, agreed against a physical reference sample rather than a colour name.
- Bar length and screw specification, cut to the coffin size you actually build.
- Packing format, including packing by the set so one carton serves one coffin.
- Dimensional changes to an existing design where the tooling allows it.
- Completely new designs tooled from a drawing, a sample or a photograph and held for your account.
Comparison With Other Products
How It Compares
| This model | Injection moulded and vacuum metallized. Light, low unit cost, rated at 50kg/pc. |
|---|---|
| Cast zamak equivalent | Heavier and more expensive per piece, with sharper cast detail and a plated rather than coated finish. |
| Unreinforced plastic | Lower cost again but decorative only. Not suitable where the piece has to carry weight. |
Use Guide
Fitting And Handling Notes
- Set out the handle positions along the coffin side and mark all screw holes before driving anything.
- Drill pilot holes in hardwood. Chipboard and MDF need the correct screw type or the thread will strip.
- Use the screw size stated in the specification. Too long and it breaks through the inside face.
- Tighten evenly across both fixing points rather than fully seating one side first.
- For a movable handle, check the bar swings and returns freely before the coffin leaves the bench.
- Never rely on fewer handles than the coffin weight calls for. Divide the loaded weight by the rated lift weight and add margin.
Related Products
More From Cremation Handle
9523Cremation Handle
ABS heavy duty resistance plastic coffin handle 9523 in copper color
PP or ABS with steel bar · lifts 50kg/pc
9524Cremation Handle
Portugal casket handle 9524 in copper color and funeral decoration
PP or ABS with steel bar · lifts 35kg/pc
9525Cremation Handle
Swing bar casket handle 9525 in PP material and copper plated
PP or ABS plastic · lifts 35kg/pc
Related Applications
Who Buys This And Why
Industry
Coffin & Casket Manufacturers
Container volume hardware with repeatable plating and matched sets for the assembly bench...
Industry
Funeral Homes & Directors
Hardware you can rely on during a service and hold as spares for repairs and refurbishment...
Industry
Importers & Distributors
A full programme from one factory so a container carries handles crucifix corners and urns together...
Industry
Cremation Providers
Light metallized fittings for coffins that will be cremated and urns for what comes after...
Related Articles
Background Reading
Buying Guide
How To Choose Coffin Handles
Fixed handles, movable swing handles, long handle bars and complete handle sets compared by load, assembly tim...
Process Guide
How Coffin Handles Are Made
The production route for funeral hardware: zamak die casting, hand polishing and electroplating for metal, inj...
Design Guide
Choosing A Finish For Coffin Hardware
Gold, nickel, antique brass, antique copper, chrome and vacuum metallized tones — how to choose a finish and h...
Installation Guide
Fitting Coffin Handles And Decoration
Practical fitting notes for coffin handles, handle bars, crucifix, corners and swing bars — screw choice, spac...
Download the Plastic Handle catalogue
Every reference in this range with images and specifications, as a PDF.
Questions
Questions About This Product
What is the minimum order quantity for this item?
The minimum order quantity for reference 9522 is 1000pcs. Minimums vary by product because the tooling and the plating batch size differ, so please confirm with our sales team before you plan an order.
How long is the lead time?
Lead time for this item is 30days after the order is confirmed. We sometimes hold stock, so if you need goods urgently it is worth asking before you assume the full lead time applies.
Which finishes are available?
This item is produced in Gold, Silver or Copper. We agree the tone against a physical sample rather than a colour name, and keep that reference so a repeat order starts from the same point.
What does the lift weight rating mean?
It is the load one piece is rated to carry, 50kg/pc in this case. Divide the loaded coffin weight by that figure to work out how many pieces the coffin needs, then add margin. Load bearing models are checked on our own lift weight test rig.
Can I get a sample before placing a bulk order?
Yes. We can provide samples for most of our products. Contact the sales team to discuss the details and the cost of the sample.
Can this design be customised?
Yes. We develop our own moulds at the Wenzhou factory, so size, finish and detail changes are possible, and completely new designs can be tooled from a drawing, a sample or a photograph.
Do you ship internationally?
Yes, we ship worldwide, FCL or LCL. Most of our production goes to Europe. Contact the sales department for freight cost and transit time to your location.
Next Step
Get A Price For This Reference
Send the reference number and the quantity you need. We will come back with unit price, minimum order quantity, lead time and the finish options for this model.
WhatsApp +86 138 1154 0649 · [email protected] · +86-316-5997244