Home / Products / Casket Corner & Swing Bar / Swing Bar / Plastic panel and pipe cap casket swing bar in set 2009
Swing Bar
Plastic panel and pipe cap casket swing bar in set 2009
Ref 2009
plastic and steel
Lifts 300kg/pc
MOQ 100sets
Plastic panel and pipe cap casket swing bar in set 2009, funeral casket handle, plastic coffin handle, funeral products for casket
The swing bar 2009, it supply by set, each set including 2pcs of short handle in 38cm and 2pcs of long bar handle in 174cm, the short handle with 2pcs of plastic panel, 2pcs of plastic end cap, 2pcs of zamak hinge, and 1pc of steel pipe, and the long bar bar handle have 8pcs of plastic panel, 2pcs of plastic end cap, 8pcs of zamak hinge, and 1pc of long steel pipe. It can lift 300kg per set. The color can be gold, silver or bronze.
Competitive Advantage: High polished, high quality and competitive price
Drawings and reference photos are welcome on WhatsApp or by email. We do not use web forms.
Material
plastic and steel
Lift weight
300kg/pc
MOQ
100sets
Lead time
30days
Key Benefits
Why This Model Is Specified
Tested Lift Weight
This model is rated at 300kg/pc. Load bearing models are checked on our own lift weight rig rather than quoted from a catalogue.
Steel Where It Carries Load
A steel bar or steel core carries the bearing load while the casting or moulding carries the appearance.
Light And Low Cost
Injection moulded and vacuum metallized, so the piece reads as metal at a fraction of the weight and unit cost.
Finish Options
Available in Gold, Silver or Bronze. The approved tone is recorded so a repeat order matches the first one.
Hand Polished Before Finishing
Plating cannot hide a poor surface, so cast parts are hand polished before they go to the plating line.
Made On Our Own Tooling
The mould is ours and sits in our Wenzhou factory, so a re-order runs from the same tool rather than a copy.
Application Scenarios
Where It Is Used
- Full length swing bar casket hardware
- Corner decoration on wooden and metal caskets
- Matched sets of corner, bar and lid fittings
- Refurbishment of existing casket ranges
Who It Is For
Buyers Who Specify This Item
- American style casket manufacturers
- Coffin factories adding a swing bar range
- Funeral hardware importers and wholesalers
- Funeral homes and funeral directors
Problems It Solves
What Goes Wrong Without It
- Fittings sold without a stated load figure. This one is rated at 300kg/pc per piece.
- Plating tone that drifts between orders so a re-order will not sit next to earlier stock.
- Waiting on a supplier who has to sub-contract the tooling before anything can be made.
- Small parts that no factory wants to quote because the volume is modest.
Not sure this is the right reference?
Send a photo of the fitting you are trying to match on WhatsApp and we will identify the closest reference in our catalogue.
Talk To An EngineerTechnical Features
Specification Summary
| Material | plastic and steel |
|---|---|
| Production route | Injection and vacuum metalization coating |
| Finish options | Gold, Silver or Bronze |
| Rated lift weight | 300kg/pc |
| Long bar length | 174cm |
| Short bar length | 38cm |
| Standard set detail | 2pcs of 38cm handle and 2pcs of 174cm long bar |
Specifications
Full Specification Table
| Ref No. | 2009 |
|---|---|
| Lift weight | 300kg/pc |
| Production Route | Injection and vacuum metalization coating |
| Material | plastic and steel |
| Long bar length | 174cm |
| Short bar length | 38cm |
| Standard set detail | 2pcs of 38cm handle and 2pcs of 174cm long bar |
| Finish | Gold, Silver or Bronze |
| MOQ | 100sets |
| Lead Time | 30days |
Figures are taken from our production specification for this reference. Where a value is not listed we would rather leave it blank than estimate it, so please ask and we will confirm from the factory.
Materials And Manufacturing Process
How This Item Is Produced
Material for this reference is plastic and steel. The stated production route is Injection and vacuum metalization coating.
Tooling
The mould is cut and trialled in our own workshop.
Injection
ABS or PP is injection moulded to the mould form.
Vacuum metallizing
A metal layer is deposited under vacuum.
Colour coating
Gold, silver, copper or bronze tone is coated over the metallized layer.
Inspection and packing
Pieces are checked for coating defects, counted and packed.
Quality Control
What We Check Before Packing
- Incoming material is checked before it goes into the casting or moulding cell.
- Castings and mouldings are inspected in process, not only at the end of the line.
- Load bearing models are checked on our own lift weight test rig.
- Plating and coating tone is compared against the approved reference sample.
- Counting and packing are checked before the carton is closed.
Documents
What Can Travel With The Order
Packing list, material description and the lift weight test record for load bearing models can be issued with the shipment. Ask before the order is confirmed so the paperwork is prepared in time.
Customization Options
What Can Be Changed
- Finish and tone, agreed against a physical reference sample rather than a colour name.
- Bar length and screw specification, cut to the coffin size you actually build.
- Packing format, including packing by the set so one carton serves one coffin.
- Dimensional changes to an existing design where the tooling allows it.
- Completely new designs tooled from a drawing, a sample or a photograph and held for your account.
Comparison With Other Products
How It Compares
| This model | Die cast in plastic and steel, hand polished and electroplated, rated at 300kg/pc. |
|---|---|
| Metallized plastic equivalent | Lower unit cost and lighter, suited to cremation coffins, with a coated rather than plated finish. |
| Stamped steel fitting | Cheaper again but flatter in profile, with far less ornament detail available. |
Use Guide
Fitting And Handling Notes
- Fit the corners first, check the bar swings clean of the casket body, then fix the bar.
- Both corners on one end must sit at the same height or the bar will bind as it swings.
- Use the screw size stated in the specification and drill pilot holes in hardwood.
- Check the swing action with the lid closed before the casket leaves the bench.
Related Products
More From Swing Bar
2007Swing Bar
Last supper design casket handle 2007 in gold color
plastic and steel · lifts 300kg/pc
2010Swing Bar
Funeral accessories casket swing bar set decoration 2010
plastic and steel · lifts 300kg/pc
Related Applications
Who Buys This And Why
Industry
Coffin & Casket Manufacturers
Container volume hardware with repeatable plating and matched sets for the assembly bench...
Industry
Funeral Homes & Directors
Hardware you can rely on during a service and hold as spares for repairs and refurbishment...
Industry
Importers & Distributors
A full programme from one factory so a container carries handles crucifix corners and urns together...
Industry
Cremation Providers
Light metallized fittings for coffins that will be cremated and urns for what comes after...
Related Articles
Background Reading
Material Guide
Coffin Hardware Materials Compared
Zamak, steel, stainless steel, brass, aluminium, ABS and PP for coffin handles, crucifix and casket fittings —...
Process Guide
How Coffin Handles Are Made
The production route for funeral hardware: zamak die casting, hand polishing and electroplating for metal, inj...
Design Guide
Choosing A Finish For Coffin Hardware
Gold, nickel, antique brass, antique copper, chrome and vacuum metallized tones — how to choose a finish and h...
Installation Guide
Fitting Coffin Handles And Decoration
Practical fitting notes for coffin handles, handle bars, crucifix, corners and swing bars — screw choice, spac...
Download the Casket Corner & Swing Bar catalogue
Every reference in this range with images and specifications, as a PDF.
Questions
Questions About This Product
What is the minimum order quantity for this item?
The minimum order quantity for reference 2009 is 100sets. Minimums vary by product because the tooling and the plating batch size differ, so please confirm with our sales team before you plan an order.
How long is the lead time?
Lead time for this item is 30days after the order is confirmed. We sometimes hold stock, so if you need goods urgently it is worth asking before you assume the full lead time applies.
Which finishes are available?
This item is produced in Gold, Silver or Bronze. We agree the tone against a physical sample rather than a colour name, and keep that reference so a repeat order starts from the same point.
What does the lift weight rating mean?
It is the load one piece is rated to carry, 300kg/pc in this case. Divide the loaded coffin weight by that figure to work out how many pieces the coffin needs, then add margin. Load bearing models are checked on our own lift weight test rig.
Can I get a sample before placing a bulk order?
Yes. We can provide samples for most of our products. Contact the sales team to discuss the details and the cost of the sample.
Can this design be customised?
Yes. We develop our own moulds at the Wenzhou factory, so size, finish and detail changes are possible, and completely new designs can be tooled from a drawing, a sample or a photograph.
Do you ship internationally?
Yes, we ship worldwide, FCL or LCL. Most of our production goes to Europe. Contact the sales department for freight cost and transit time to your location.
Next Step
Get A Price For This Reference
Send the reference number and the quantity you need. We will come back with unit price, minimum order quantity, lead time and the finish options for this model.
WhatsApp +86 138 1154 0649 · [email protected] · +86-316-5997244