Home / Products / Metal Crucifix & Fittings / Casket Fittings / Casket armed hinge 8507, antique brass color and zamak...
Casket Fittings
Casket armed hinge 8507, antique brass color and zamak material
Ref 8507
Zamak#3 with steel basement and screw bolt and nuts
Lifts 100kg/pc
MOQ 2000pcs
The 8507 is used in casket handle and fitting, it also the good decoration for the wooden casket, it will be good apperance and high polish. It can complied with the end cap 8511, 8512 and 8513.
Competitive Advantage: High polished, high quality and competitive price
Casket handle end tips and funeral casket hardware 8512 in Electronic Plated
Drawings and reference photos are welcome on WhatsApp or by email. We do not use web forms.
Material
Zamak#3 with steel basement and screw bolt and nuts
Lift weight
100kg/pc
MOQ
2000pcs
Lead time
30days
Key Benefits
Why This Model Is Specified
Tested Lift Weight
This model is rated at 100kg/pc. Load bearing models are checked on our own lift weight rig rather than quoted from a catalogue.
Zamak #3 Casting
Die cast in Zamak #3, which holds fine ornament detail and stays dimensionally stable, so the hundredth piece matches the first.
Steel Where It Carries Load
A steel bar or steel core carries the bearing load while the casting or moulding carries the appearance.
Finish Options
Available in Gold, Antique Brass or Antique Copper. The approved tone is recorded so a repeat order matches the first one.
Hand Polished Before Finishing
Plating cannot hide a poor surface, so cast parts are hand polished before they go to the plating line.
Made On Our Own Tooling
The mould is ours and sits in our Wenzhou factory, so a re-order runs from the same tool rather than a copy.
Application Scenarios
Where It Is Used
- Coffin and casket lid decoration
- Interior placement inside the casket
- Name plates and memorial plaques
- Cross and crucifix fixed to tombstones and monuments
Who It Is For
Buyers Who Specify This Item
- Coffin and casket manufacturers
- Funeral hardware importers and wholesalers
- Funeral homes and funeral directors
- Traders and buying offices sourcing funeral hardware from China
Problems It Solves
What Goes Wrong Without It
- Fittings sold without a stated load figure. This one is rated at 100kg/pc per piece.
- Plating tone that drifts between orders so a re-order will not sit next to earlier stock.
- Waiting on a supplier who has to sub-contract the tooling before anything can be made.
- Small parts that no factory wants to quote because the volume is modest.
Not sure this is the right reference?
Send a photo of the fitting you are trying to match on WhatsApp and we will identify the closest reference in our catalogue.
Talk To An EngineerTechnical Features
Specification Summary
| Material | Zamak#3 with steel basement and screw bolt and nuts |
|---|---|
| Production route | Die casting, polish and electronic plating |
| Finish options | Gold, Antique Brass or Antique Copper |
| Rated lift weight | 100kg/pc |
Specifications
Full Specification Table
| Ref No. | 8507 |
|---|---|
| Lift weight | 100kg/pc |
| Production Route | Die casting, polish and electronic plating |
| Material | Zamak#3 with steel basement and screw bolt and nuts |
| Finish | Gold, Antique Brass or Antique Copper |
| MOQ | 2000pcs |
| Lead Time | 30days |
Figures are taken from our production specification for this reference. Where a value is not listed we would rather leave it blank than estimate it, so please ask and we will confirm from the factory.
Materials And Manufacturing Process
How This Item Is Produced
Material for this reference is Zamak#3 with steel basement and screw bolt and nuts. The stated production route is Die casting, polish and electronic plating.
Tooling
The die is cut and trialled in our own workshop.
Die casting
Zamak #3 is die cast on our casting machines.
Hand polishing
Every casting is hand polished before it reaches the plating line.
Electroplating
Gold, nickel, antique brass, antique copper or chrome.
Assembly and packing
Bars, caps and screws are matched, then counted and packed.
Quality Control
What We Check Before Packing
- Incoming material is checked before it goes into the casting or moulding cell.
- Castings and mouldings are inspected in process, not only at the end of the line.
- Load bearing models are checked on our own lift weight test rig.
- Plating and coating tone is compared against the approved reference sample.
- Counting and packing are checked before the carton is closed.
Documents
What Can Travel With The Order
Packing list, material description and the lift weight test record for load bearing models can be issued with the shipment. Ask before the order is confirmed so the paperwork is prepared in time.
Customization Options
What Can Be Changed
- Finish and tone, agreed against a physical reference sample rather than a colour name.
- Bar length and screw specification, cut to the coffin size you actually build.
- Packing format, including packing by the set so one carton serves one coffin.
- Dimensional changes to an existing design where the tooling allows it.
- Completely new designs tooled from a drawing, a sample or a photograph and held for your account.
Comparison With Other Products
How It Compares
| This model | Die cast in Zamak#3 with steel basement and screw bolt and nuts, hand polished and electroplated, rated at 100kg/pc. |
|---|---|
| Metallized plastic equivalent | Lower unit cost and lighter, suited to cremation coffins, with a coated rather than plated finish. |
| Stamped steel fitting | Cheaper again but flatter in profile, with far less ornament detail available. |
Use Guide
Fitting And Handling Notes
- Mark the centre line of the lid first and set the piece out from that line, not from an edge.
- Use the screw size stated in the specification. A longer screw can break through a thin lid panel.
- Drill a pilot hole in hardwood. Driving straight into hardwood can split the panel or strip the casting.
- Fit decoration after the coffin is polished, so polish and wax do not build up around the ornament.
- Where the piece will be fixed outdoors on stone, ask for the stainless or brass version instead.
Related Products
More From Casket Fittings
8511Casket Fittings
Metal End Cap for Casket Handle 8511 End Tips and Funeral Casket Hardware
Zinc Alloy (metal)
8512Casket Fittings
Casket handle end tips and funeral casket hardware 8512 in Electronic Plated
Zamak #3
8513Casket Fittings
Zinc Alloy Casket Handle End Tip 8513 by Die Casting and Electronic Plated in Metal Hardware for Casket
Zinc Alloy (metal)
8517Casket Fittings
Metal Hinge 8517 Knock Down In Wooden Casket Lid And Funeral Fittings
Steel (Iron)
8518Casket Fittings
Metal Latch And Lock 8518 In Wooden Casket Lid And Funeral Hardware
Steel (Iron)
8522Casket Fittings
Casket Arm 8522 in Antique Copper and Screw Rod Metal Handle For Casket
Steel (iron) · lifts 100kgs/pc
Related Applications
Who Buys This And Why
Industry
Coffin & Casket Manufacturers
Container volume hardware with repeatable plating and matched sets for the assembly bench...
Industry
Funeral Homes & Directors
Hardware you can rely on during a service and hold as spares for repairs and refurbishment...
Industry
Importers & Distributors
A full programme from one factory so a container carries handles crucifix corners and urns together...
Industry
Cremation Providers
Light metallized fittings for coffins that will be cremated and urns for what comes after...
Related Articles
Background Reading
Material Guide
Coffin Hardware Materials Compared
Zamak, steel, stainless steel, brass, aluminium, ABS and PP for coffin handles, crucifix and casket fittings —...
Process Guide
How Coffin Handles Are Made
The production route for funeral hardware: zamak die casting, hand polishing and electroplating for metal, inj...
Design Guide
Choosing A Finish For Coffin Hardware
Gold, nickel, antique brass, antique copper, chrome and vacuum metallized tones — how to choose a finish and h...
Installation Guide
Fitting Coffin Handles And Decoration
Practical fitting notes for coffin handles, handle bars, crucifix, corners and swing bars — screw choice, spac...
Download the Metal Crucifix & Fittings catalogue
Every reference in this range with images and specifications, as a PDF.
Questions
Questions About This Product
What is the minimum order quantity for this item?
The minimum order quantity for reference 8507 is 2000pcs. Minimums vary by product because the tooling and the plating batch size differ, so please confirm with our sales team before you plan an order.
How long is the lead time?
Lead time for this item is 30days after the order is confirmed. We sometimes hold stock, so if you need goods urgently it is worth asking before you assume the full lead time applies.
Which finishes are available?
This item is produced in Gold, Antique Brass or Antique Copper. We agree the tone against a physical sample rather than a colour name, and keep that reference so a repeat order starts from the same point.
What does the lift weight rating mean?
It is the load one piece is rated to carry, 100kg/pc in this case. Divide the loaded coffin weight by that figure to work out how many pieces the coffin needs, then add margin. Load bearing models are checked on our own lift weight test rig.
Can I get a sample before placing a bulk order?
Yes. We can provide samples for most of our products. Contact the sales team to discuss the details and the cost of the sample.
Can this design be customised?
Yes. We develop our own moulds at the Wenzhou factory, so size, finish and detail changes are possible, and completely new designs can be tooled from a drawing, a sample or a photograph.
Do you ship internationally?
Yes, we ship worldwide, FCL or LCL. Most of our production goes to Europe. Contact the sales department for freight cost and transit time to your location.
Next Step
Get A Price For This Reference
Send the reference number and the quantity you need. We will come back with unit price, minimum order quantity, lead time and the finish options for this model.
WhatsApp +86 138 1154 0649 · [email protected] · +86-316-5997244